Visit our Ebay store
for more products
Visit Calvert Racing Suspensions
for more products
BSPP Tapered To AN Male Adapter
1/8" to -6AN, Silver Finish
$5.39
AF950-08-04BLK FEMALE REDUCER -8AN TO -4AN BLACK REDUCER FEMALE TO MALE
$15.00
Wilwood Front Brake Rotor Drilled&Slotted ZINC 11inch R/H
$156.18
WELD 788B-509276F ALUMASTAR 2.0 (SINGLE BEAD LOCK) 15" X 9.0", 5 X 4.75" BC, 3.00" BS, HQ, CHEV (GM) BLACK
$1,384.00
45° Male ORB Full Flow Swivel Hose End -8 ORB to -10AN
Silver Finish
$32.00
Black Steel Valve Covers
Suit SB Chev Without Aeroflow Logo, Tall
$32.89
Dual Outlet EFI Pump Surge Tank - Polished
with Dual -8 ORB
$93.39
45° NPT Swivel to Male AN Flare Adapter 1/2" to -12AN
Black Finish
$40.39
3-Bolt Stainless Steel Flange
2-1/2" (63.5mm) I.D x 3/8" (9.52mm) Thick
$96.69
MT-3481 Mickey Thompson ET Street S/S Radial Tyre 285 x 40 x 18 Blackwall, R2 Compound
$535.00
Visit our Ebay store
for more products
Spark Plug Boot Protector - 150mm Length
Black slip on design, withstands 500°F direct heat & 2000°F radiant heat, 4 pack
$39.80
AN Tee Female Swivel On Side -4AN
Blue Finish
$18.03
45° NPT to Male Flare Adapter 1/8" to -3AN
Silver Finish
$8.25
90° AN Bulkhead -6AN
Blue Finish
$11.04
AFR-1137-TI AFR NPP SBC Eliminator Racing Cylinder Heads, 23 deg, Angle Plug, 245cc Intake, 70cc Chamber, Chev S/B (Pair)
$5,425.00
Comp Cams Pro Magnum(anti pump up) Hyd Flat Tappet Suit Mopar 273-360 383-440
$184.00
Stainless Steel 90° Banjo to AN Fitting
11.2mm (7/16") Banjo to -3AN Male
$26.41
AEROFLOW PRO FILTER 60 MICRON BLACK FEMALE -8 ORB 1.25"x3.5" Aeroflow - AF 66-2042BLK
$115.52
Tube to Female AN Adapter 5/8" to -10AN
Black Finish. Suits Aeroflow, Moroso & Russell Tubing
$23.62
Stainless Steel Washer Seal Adapter -3AN
M10 x 1.25mm
$12.44
Our customer is a Champion Super Street Drag Racer and he asked us to develop a stainless steel wire mesh carburetor screen to cover the carburetor on his drag car.
The proper design for the carburetor screen needed to have mesh fine enough to keep out small stones, tools and rags, but be open enough to allow maximum air flow. The screen had fit snuggly on the face of the carburetor so it wouldn’t rattle at high RPMs. And it needed several grommeted holes for the hold down post and carburetor float vent tubes.
The Carburetor Screen we developed for our customer uses 6 mesh x 0.028″ woven wire mesh which has a 0.138″ opening and a 69% open space. Grommets are installed in several holes and the mesh is formed into a shallow bowl shape in a hydraulic press. Then a stainless steel band is welded to the bottom edge.
© Competition Engines 2010-2024